Menu

Design notes

How we make hardware decisions: power and batteries, mechanical design, circuit boards, radio and certification.

Mechanical design 9

Aluminium, Steel, or PlasticAluminium, steel, or plastic? The material decides the cost, the weight, the heat, the EMI, and whether the product survives outdoors, and the wrong one fails in under two years. Three axes, four plastics, three metals, and the arithmetic for Example Labs' field sensor hub.20 minCNC Machining DFMA 30 mm deep pocket with R2 corners forces a 4 mm end mill that deflects 16 times more than the tool the job needs, and a drawing with ±0.01 mm on every dimension costs eight times the same part at ±0.5 mm. Eight design rules, each with a number, and a machined sensor hub worked from $1,370 a part to $430.25 minEnclosures That Survive the Real WorldIP67 is a laboratory test on a new unit, for thirty minutes. It says nothing about year two, when the gasket has taken a compression set and the box has baked in the sun. A sealed 100 × 60 × 40 mm box with 5 W inside runs 25 °C hotter than the air around it. The enclosure is not a box, it is a promise: keep the water out, let the heat out, and open again when something breaks.14 minInjection Moulding DFMInjection molding design determines 70–80% of final part cost and quality before production begins. The five rules are simple: a uniform 1.5–3.0 mm wall, 1–3° of draft per side, ribs at half the wall, bosses at six-tenths, and shrinkage built into the cavity, PP shrinks 1.0–2.5%, so a 100 mm part needs a cavity of 101–102.5 mm. Roughly 70% of first-submission designs contain at least one feature that would cause a defect or force an expensive mould action, and one post-tooling modification typically costs $2,000–$20,000 and 2–6 weeks. The fix is a CAD edit, not a tool edit.19 minSheet Metal DFMYour enclosure came back 7 millimetres too wide, with a cracked bend and a hole stretched into a slot. Sheet metal is not machining, the flat pattern is the part, and the bend is where the size lives. Twelve rules, in the order you meet them on a model.17 minThe Clip That Doesn't BreakThe lid has to open for battery service and calibration, and every time it opens, the clip bends past its limit, because the clip is a spring, and the spring was sized by feel instead of by strain.21 minThe Screw That Doesn't StripThe housing has to open for battery service and calibration, and every time it opens, the joint gets weaker. A self-tapping screw holds 380 N on the first pass and is stripped by the eleventh; a brass insert still holds 1,056 N at pass 25. The strength does not come from the brass, it comes from plastic locked into the knurls.21 minThe Seal That Actually SealsYour enclosure passed IP65 on the bench and leaks in the field, because the gasket took a set after two years of temperature cycling and the joint designed at 30% compression is now working at 15%. The seal is a set of numbers, not a material.26 minTolerance Stack-UpEvery part is a little off, and the little offs add up. Ten parts at ±0.1 mm stack to ±1.00 mm worst case and ±0.32 mm statistically, and the difference between those two answers is the difference between a product that assembles and a product that doesn't. The fix is rarely a tighter tolerance. It is usually a shorter chain.14 min

Power and batteries 6

Power Design for Battery ProductsThe battery is a budget, not a box. A field sensor on a CR2032: the headline budget says 513 days, the measured budget says 44. The gap is sleep current, regulator losses, and a battery that is not a constant, and the fix is arithmetic, not a bigger cell. The power budget, the BMS, and the rules that make battery life honest.14 minThe Battery's BrainA battery management system is three things at once: the eyes that measure every cell, the accountant that estimates how much charge is left, and the guard that disconnects the pack before a fault becomes a fire. This is how to design each one, the measurement accuracy that decides how much capacity you waste, the SOC estimation that has no sensor to read, the balancing choice, and the protection thresholds with real margin, with a worked demo on a 48 V pack.28 minThe Pack That Doesn't Drift ApartThe pack is rated 168 watt-hours and delivers 160, because the fullest cell ends every charge and the emptiest ends every discharge, and the 8 watt-hours in between are locked away behind the weakest cell.23 minThe Shipment That Gets SeizedYour lithium battery cannot ship without UN38.3, eight tests, sixteen packs destroyed, four to six weeks, and a test summary the carrier will ask for by name. Here is what each test does, what it costs, and what happens when one fails.24 minThermal RunawayThermal runaway is a self-accelerating failure: the cell makes heat faster than it can shed it, and each reaction makes the next one hotter, until the cell vents flammable gas and may ignite, at internal temperatures over 800 °C. One cell in Example Labs' 74.9 Wh pack holds 33,696 J, and heating it from 25 °C to 200 °C takes only 23% of that energy, so the BMS disconnect does not save the cell, it buys time for the other layers. The barrier is the layer that decides whether the pack survives: it must block 86% of the failing cell's heat to keep the neighbour below the 130 °C separator melt, and a ceramic fibre barrier slows propagation by more than 30×, turning 10–30 seconds into 5–15 minutes.16 minUSB-C Power DeliveryEvery USB-C plug fits every USB-C socket, and almost nothing else about a cable is guaranteed. The CC resistors that set the first 15 W, the four-message negotiation, the 240 W EPR ladder, the e-marker that gates it, and the EU rule that now makes it law.23 min

Testing, safety and certification 3

CE markingOn Wednesday 20 January 2027, Regulation (EU) 2023/1230 applies in full and Directive 2006/42/EC is repealed, a hard cut-over, unit by unit, with no grace period for new machines built to the old Directive. The Regulation adds essential requirements the Directive never had: protection against corruption, software and update integrity, self-evolving behaviour, and AI in safety functions, and for the six Annex I Part A categories, a notified body is always mandatory. Example Labs' cobot cell costs €6,625 in testing without the AI safety function and €16,625 with it, and the notified-body route lands February–May 2027, after the deadline.21 minHuman FactorsIEC 62366-1:2015+AMD1:2020 is the international standard for usability engineering of medical devices, recognised by FDA as a consensus standard, and FDA's guidance 'Applying Human Factors and Usability Engineering to Medical Devices' (2016, revised August 2026) sets what reviewers expect. The process: specify users and use environment, identify use-related hazards, design the interface to mitigate them, validate with representative users. Formative testing uses early prototypes with 5–8 participants per user group; summative validation uses the finalised, production-equivalent device with at least 15 participants per distinct user group. On average 85% of utilisation problems are found with 5 representative users, 95% with 10. Between 2012 and 2015 there were 423 medical device recalls resulting from UI software errors. Acceptance is the correct execution of a task without use errors or difficulties, a percentage of users completing a task in a time is not a pass mark, because the users who cannot complete it are the signal, not the noise.24 minComponent deratingYour board was designed at the ratings, and now the warranty claims are coming in, slow drift, not sudden death. Here is the derating table that makes the product last: the 50% rule, NASA's table, the tantalum numbers, and what MTBF actually means.19 min